Automotive IC

___Other Application IC > Automotive IC___

___Part No.___ ______ (勾選方式)	___Features___	___VCC(V)___	___Package___
___93334___	___High Energy Ignition Circuit___ ______ ___* Very Low Peripheral Component Count___ ___* No Critical System Resistors___ ___* Wide Supply Voltage Operating Range (4.0V ~ 24V)___ ___* Overvoltage Shutdown (30V)___ ___* Dwell Automatically Adjusts to Produce Optimum Stored Energy___ ___without Waste___ ___* Externally Adjustable Peak Current___ ___* Transient Protected Inputs and Outputs___	___4.0~24.0___	___SOP-8___
___M4213___	___Ignition Controller of Motorcycle___ ______ ___* Power supply by magnetoelectric motor and clamping at 9.2V___ ___* Less external components and wide applicability___ ___* Low static current, typical is 5mA___ ___* High quality and stability for using 5μm Bipolar process___	___9.0~9.5___	___DIP-14___ ___SOP-14___
___UL497___	___Hall Effect Pickup Ignition Controller___ ______ ___* Direct driving of the external power darlington___ ___* Coil current charent charging angle control___ ___* Programme coil current peak limitation___ ___* When 94% nominal current not reached programmable dwell___ ___recovery time___ ___* RPM output___ ___* Has peranent conduction protection___ ___* Overvoltage protection___ ___* Internal supply zener___ ___* Reverse battery protection___	___3.5___	___SOP-16___
___UU6043B___	___Single Output Flasher IC for 18mohm shunt___ ______ ___Temperature and supply voltage compensated frequency___ ___* Warning indication of lamp failure by means of frequency___ ___doubling___ ___* Relay driver output with high current carrying capacity and low___ ___saturation output___ ___* Minimum lamp load for flasher operation: ≥ 1 W___ ___* Very low susceptibility to EMI___	___9.0~15.0___	___SOP-8___ ___DIP-8___
___UU4761___	___FLASHER IC___ ______ ___* The static operating current<5mA___ ___* Wide operating voltage range___ ___* Very low susceptibility to EMI___	___9.5~18.0___	___SOP-8___ ___DIP-8___
___U2043___	___Flasher, Shunt, Pilot Lamp to GND or Vbatt___ ______ ___Temperature and voltage compensated frequency___ ___Warning indication of lamp failure by means of frequency doubling___ ___* Minimum lamp load for flasher operation ≥10 W___ ___Relay output with high current carrying capacity and low saturation___ ___voltage___ ___Low susceptibility to EMI___	___9.0~15.0___	___SOP-8___ ___DIP-8___
___L2044___	___Dual Output Flasher___ ______ ___* Temperature and Supply Voltage Compensated Flashing___ ___Frequency___ ___* Frequency Doubling Indicates Lamp Fault.___ ___* Two Relay Driver Outputs with High Current-carrying Capacity___ ___and Low Saturation Voltage___ ___* Minimum Lamp Load for Flasher Operation: ≥ 1W___ ___* Very Low Sensitivity to EMI___ ___* Extremely Low Current Consumption<10μA ( at Switches Open)___ ___* Reverse Polarity Protection___ ___* Three Control Inputs: Left, Right and Hazard Warning___	___8.0~18.0___	___SOP-14___ ___DIP-14___
___LL204___	___DUAL OUTPUT FLASHER___ ______ ___* Temperature and supply voltage compensated flashing frequency___ ___* Frequency doubling indicates lamp fault.___ ___* Two relay driver outputs with high current-carrying capacity and low___ ___saturation voltage___ ___* Minimum lamp load for flasher operation: ≥ 1W___ ___* Very low sensitivity to EMI___ ___* Extremely low current consumption<10μA ( at switches open)___ ___* Reverse polarity protection___ ___* Three control inputs: left, right and hazard warning___	___8.0~18.0___	___SOP-14___ ___DIP-14___
___UU6032B___	___Automotive toggle switch IC___ ______ ___* Relay driver with Z-diode___ ___* RC oscillator determines switching characteristics___ ___* Debounced input for toggle switch___ ___* Three debounced inputs: ON, OFF and TOGGLE___ ___* RF interference protection___ ___* Load-dump protection___	___6.0~16.0___	___SOP-8___ ___DIP-8___
___UU6046B___	___Rear window heating timer___ ______ ___* Delay time range: 3.7s to 20h___ ___* Relay driver with Z-diode___ ___* RC oscillator determines switching characteristics___ ___* Debounced input for toggle switch___ ___* Two debounced inputs: ON and OFF___ ___* Load-dump protection___ ___* RF interference protected___ ___* Inputs switched to VBatt___	___6.0~16.0___	___SOP-8___ ___DIP-8___
___UU6047B___	___Rear window heating timer___ ______ ___* Delay time range: 3.7s to 20h___ ___* Relay driver with Z-diode___ ___* RC oscillator determines switching characteristics___ ___* Debounced input for toggle switch___ ___* Two debounced inputs: ON and OFF___ ___* Load-dump protection___ ___* RF interference protected___ ___* Inputs switched to ground___	___6.0~16.0___	___SOP-8___ ___DIP-8___
___UU642___	___INTERVAL AND WIPE/WASH WIPER CONTROL IC___ ______ ___* After-wiping time: 2s~20s___ ___* Interval pause: 4s~20s___ ___* Wipe/wash mode priority___ ___* Wiper motor’s park switch___ ___* Relay driver with Z-diode___ ___* One external capacitor determines all time sequences___ ___* Interference protection according to VDE 0839 or ISO/TR 637/1___ ___* Load-dump protected___	___9.0~16.5___	___SOP-8___ ___DIP-8___
___UAC33092___	___Alternator Voltage Regulator___ ______ ___Forced Load Response Control (LRC) with Heavy Load Transitions___ ___at Low RPM___ ___Capable of Regulating Voltage to ±0.1 V @ 25℃___ ___Operating Frequency Selectable with One External Resistor___ ___< 0.1 V Variation over Speed Range of 2000 to 10,000 RPM___ ___< 0.4 V Variation over 10% to 95% of Maximum Alternator Output___ ___Maintains Regulation with External Loads as Low as 1.0 A___ ___Load Dump Protection of Lamp, Field Control Devices, and Loads___ ___Duty Cycle Limit Protection___ ___Provides High Side MOSFET Control of a Ground Referenced Field___ ___Winding___ ___Controlled MOSFET and Flyback Diode Recovery Characteristics___ ___for Minimum RFI___ ___Optional 2.5 or 10 sec. LRC Rate Control (Osc. Freq. = 280 kHz)___ ___Undervoltage, Overvoltage and Phase Fault (Broken Belt) Detection___	___11.5~16.5___	___SOP-20___ ___SOP-24___
___UAC33092A___	___Alternator Voltage Regulator___ ______ ___* Forced load response control (LRC) with heavy load transitions___ ___at low RPM___ ___* Voltage regulated to ± 0.1V @ 25°C___ ___* External resistor adjustable operating frequency___ ___* Regulation is effective with loads as high as 1.0A___ ___* Load dump protection of lamp, field control devices, and loads___ ___* Undervoltage, overvoltage , phase fault (broken belt) detection___ ___and duty cycle limited protections___	___11.5~16.5___	___SOP-20___
___UU4793___	___Overload Monitoring with Resistive Load, VT = 44.5 mV___ ______ ___* Two common reference comparators___ ___* Tight threshold tolerance___ ___* Constant threshold___ ___* Output with NPN___ ___* 8 kV - ESD protection___ ___* Protection of reverse polarity___ ___* Load-dump protection___	___9.0~15.0___	___SOP-8___
___UL497___	___Hall Effect Pickup Ignition Controller___ ______ ___* Direct driving of the external power darlington___ ___* Coil current charent charging angle control___ ___* Programme coil current peak limitation___ ___* When 94% nominal current not reached programmable dwell___ ___recovery time___ ___* RPM output___ ___* Has peranent conduction protection___ ___* Overvoltage protection___ ___* Internal supply zener___ ___* Reverse battery protection___	___3.5___	___SOP-16___

This site uses cookies to collect the necessary user browsing behavior so that we can provide you with a better browsing experience. Browse this site, which means you agree with "online privacy declaration."